|
|
Post by pinstryper on Feb 25, 2016 9:48:40 GMT -5
 42 5w Osram led's and this bar weighs well over 10# with sliding mounts below. Able to mount on brushguard without drilling anymore holes. |
|
|
|
Post by pinstryper on Feb 26, 2016 10:04:06 GMT -5
freaking brite to, properly aimed it is far better than stock headlamp.
4x 8/10 would fit in place of our lights, and these have a sae type beam
|
|
|
|
Post by mrgalantguy on Mar 1, 2016 10:05:21 GMT -5
Where are you planning to install the light bar? I am planning to install a light bar...not sure if I should install a roof mounted one or where the front grille/air dam opening on mine.
I follow a guy on IG because (Tito STI) he owns my favorite Impreza/WRX platform, and he replaced his oem headlight headlights with aftermarket LED units. I will try to post a pic, but looks like he removed the reflector housing and retrofitted a LED square box in its place.
|
|
|
|
Post by MonteroSportHonduras on Mar 1, 2016 12:20:09 GMT -5
Mine is a similar size. This is how I mounted it. welded a couple steel angles to the bumper mounts and bolted a light 1" tube with tabs to mount all my lights. I wanted a more elaborated light bar but the tube I have is too thin for a bender, so I left it as simple as I could and did not touch the bumper at all.    |
|
|
|
Post by pinstryper on Mar 1, 2016 16:44:22 GMT -5
I put mine in the brushguard fits nicely, and sits at headlamp level.
|
|
|
|
Post by 2002sport on Mar 2, 2016 10:17:02 GMT -5
Looks nice. Is it a spot? or flood and spot? I've got a 36" that I mounted on my roof rack, and it lights up the dirt roads nice at night.
|
|
|
|
Post by nugget on Mar 14, 2016 13:54:28 GMT -5
I put mine in the brushguard fits nicely, and sits at headlamp level. Can you please post a picture of the final install? |
|
|
|
Post by pinstryper on Mar 14, 2016 17:57:24 GMT -5
Edit
|
|
|
|
Post by pinstryper on Mar 14, 2016 18:04:31 GMT -5
 . That's better... |
|
|
|
Post by MonteroSportHonduras on Mar 15, 2016 10:08:23 GMT -5
. That's better... Id love to get a brush guard like that one |
|
|
|
Post by nugget on Mar 20, 2016 14:52:52 GMT -5
. That's better... Looks really good. How did you mount it, and what wires did you tie into? |
|
|
|
Post by pinstryper on Mar 20, 2016 16:29:08 GMT -5
I got a ridgid harness w/relay off amazon. Have not run switch to dash yet.just going to drill hola and mount it somewhere.
Did not use factory thin *** wire.
Ridgid stuff is 12g heavy duty it is.
|
|
|
|
Post by nugget on Apr 18, 2016 12:54:31 GMT -5
Looks fantastic. I picked up a few foglight switches from the junk yard to use for factory look, but may need the factory harness and relay under the hood. Didn't realize I needed to pull at the time. hindsight.
|
|
|
|
Post by pinstryper on Apr 18, 2016 15:58:11 GMT -5
That's my nexxt getting a facctory foooglite switch to use
|
|
