Post by amatti73 on Jun 7, 2010 15:13:44 GMT -5
Well, the process has begun ... Replaced lights in lampshades interior and trunk and front doors, as well as highlighting the lever KPP. it all took all day Saturday and lasted approximately 1.2 meters of ribbon! I bought a 2-meter-tape SMD 1210 (white
) Price $ 15per meter (60 LEDs), the current consumption of one branch of the 3 LEDs and a resistor is 18-20 mA, the angle of 120 degrees, the diode voltage 3.2 Volt. Most raw material intensive ceiling - between the front seats - where 10 sections of 3 LEDs, they consume the total current was 170mA (ie 10 * 17mA), so power consumption of this bubble is about 2.5 W, v.e at least 2 times less than conventional lamps (nominal, which is shitty shines yellow), while the light-pure white and brighter times 5-10.
Indeed, waiting for the evening - and the car really is flooded with bright white light (from two ceiling).The only thing under the plastic covers I have ALWAYS put the white reflectors, filters to translucent bright LEDs are not blinded.
Qualitative light lever Gearbox immediately is impossible, becausecharacters, letters and numbers on the curved fence deposited inks of different colors - black, white, blue and green (for neutral).
And in order to uniformly illuminate (not enough to erase a couple of them solvent starts to blur and black), this
colorful sandwich must be completely done by advertisers a new sticker with a black background and white letters, translucent and transparent oval windows for the red beacon-pointer-enabled transmission. I do of course have not yet done so, but must do it, and if anybody else should I simply order 10-20 - ... copies.
Lights the buttons on the tidy and panels made in a padded light bulb with a blue rubber ,,condom,, (that type of white light). So to change it on the SMD-LED I bought a 20 LED 1210 (White-White) (also 0603) to 20 cents and 40 of the SMD-resistor of 470 ohms and a power of 0.25W (1 cent) - 2 in sequence on each LED, if the sale were to 0.5 watts (but there are not) it would have to be 20 units and the resistance would be 900-950 ohms. New power consumption chain of 2 resistors and LED is 0.3 watts (have lower power consumption circuit size by 3 times). Here are the actual pictures (so far without reflectors).
Tomorrow I will make a highlight in the ashtray, dop.priborah to torpedo the rear heater, buttons and display, climate control and lay out photo. While doing that easier, so that later when fully explored the nuances could alter tidying - responsible matter. At leisure dismantled block dop.priborov.
For example the arrow on the voltmeter, I withdraw and could not, so try Nae ... Bach destiny and do no lifting. For these devices the following nuances-
- A voltmeter and oil pressure apparatus is necessary to remove the scale and courage to wipe them with a solvent deposited raznoottenochnuyu paint-it is very dense and the light through it is very bad (trying to enlighten LED). Then cut the acrylic fiber.And then make a cardboard or plastic strip for prileplivaniya tape SMD LEDs (for pressure-one segment of the 3 LEDs, and for a voltmeter - 2 segment). And yet to be drilled a hole in the acrylic where the axis of the arrow passes!
... Its for today...
By the way, I forgot to say that all the scales and devices are made without removing the shooter! " It is very important, thank God MPS super easy designed…
Sorry for my english .
) Price $ 15per meter (60 LEDs), the current consumption of one branch of the 3 LEDs and a resistor is 18-20 mA, the angle of 120 degrees, the diode voltage 3.2 Volt. Most raw material intensive ceiling - between the front seats - where 10 sections of 3 LEDs, they consume the total current was 170mA (ie 10 * 17mA), so power consumption of this bubble is about 2.5 W, v.e at least 2 times less than conventional lamps (nominal, which is shitty shines yellow), while the light-pure white and brighter times 5-10.
Indeed, waiting for the evening - and the car really is flooded with bright white light (from two ceiling).The only thing under the plastic covers I have ALWAYS put the white reflectors, filters to translucent bright LEDs are not blinded.
Qualitative light lever Gearbox immediately is impossible, becausecharacters, letters and numbers on the curved fence deposited inks of different colors - black, white, blue and green (for neutral).
And in order to uniformly illuminate (not enough to erase a couple of them solvent starts to blur and black), this
colorful sandwich must be completely done by advertisers a new sticker with a black background and white letters, translucent and transparent oval windows for the red beacon-pointer-enabled transmission. I do of course have not yet done so, but must do it, and if anybody else should I simply order 10-20 - ... copies.
Lights the buttons on the tidy and panels made in a padded light bulb with a blue rubber ,,condom,, (that type of white light). So to change it on the SMD-LED I bought a 20 LED 1210 (White-White) (also 0603) to 20 cents and 40 of the SMD-resistor of 470 ohms and a power of 0.25W (1 cent) - 2 in sequence on each LED, if the sale were to 0.5 watts (but there are not) it would have to be 20 units and the resistance would be 900-950 ohms. New power consumption chain of 2 resistors and LED is 0.3 watts (have lower power consumption circuit size by 3 times). Here are the actual pictures (so far without reflectors).
Tomorrow I will make a highlight in the ashtray, dop.priborah to torpedo the rear heater, buttons and display, climate control and lay out photo. While doing that easier, so that later when fully explored the nuances could alter tidying - responsible matter. At leisure dismantled block dop.priborov.
For example the arrow on the voltmeter, I withdraw and could not, so try Nae ... Bach destiny and do no lifting. For these devices the following nuances-
- A voltmeter and oil pressure apparatus is necessary to remove the scale and courage to wipe them with a solvent deposited raznoottenochnuyu paint-it is very dense and the light through it is very bad (trying to enlighten LED). Then cut the acrylic fiber.And then make a cardboard or plastic strip for prileplivaniya tape SMD LEDs (for pressure-one segment of the 3 LEDs, and for a voltmeter - 2 segment). And yet to be drilled a hole in the acrylic where the axis of the arrow passes!
... Its for today...
By the way, I forgot to say that all the scales and devices are made without removing the shooter! " It is very important, thank God MPS super easy designed…
Sorry for my english .