|
Post by dzuwel on Jun 17, 2011 9:26:04 GMT -5
could anyone tell me what to look at on this....just noticed today that when I push the lock button of the remote, the corner or hazard lights of my MS does not blink anymore, only the horn will sound.... but it will lock like its normal only the corner lights will not blink.... before, it will horn and corner lights blink 2 times simultaenously... I know that this is not a big deal but I just want to know whats wrong with it. the signal or hazard lights works when your inside using it so i dont think its the fuse .....tnx
|
|
|
Post by dzuwel on Jun 18, 2011 7:18:44 GMT -5
bump..
|
|
|
Post by mxmikie on Jun 27, 2011 16:23:08 GMT -5
change the battery in the remote
|
|
|
Post by dzuwel on Jun 28, 2011 6:36:37 GMT -5
wow really! ok i'll try that one, tnx a lot mx..
|
|
|
Post by dzuwel on Jun 29, 2011 9:05:42 GMT -5
Ooops I changed the battery in the remote and its still the same, no blinking light when pressed lock....
|
|
|
Post by buggzyy on Jul 7, 2011 18:31:39 GMT -5
Are the light bulbs burned out? if not for some reason the Keyless system has lost it option program you can set the answerback function, by
ENABLING/DISABLING THE HAZARD/TURN SIGNAL ANSWERBACK FUNCTION
The answerback function from the hazard/turn signals when the doors are locked and unlocked can be turned on and off separately. A tone alarm/buzzer will sound once when the function is turned on and twice when the function is turned off. Before proceeding with the following procedures, make sure the key is removed from the ignition switch.
1. Press and hold the UNLOCK button for 4 to 10 seconds, then press and hold the LOCK button during this time. 2. To turn the function on or off when the doors are locked, release the LOCK button and then release the UNLOCK button. A tone alarm/buzzer will sound once when the function is turned on and twice when the function is turned off. 3. To turn the function on or off when the doors are unlocked, release the UNLOCK button and then release the LOCK button. A tone alarm/buzzer will sound once when the function is turned on and twice when the function is turned off. ENABLING/DISABLING THE HORN ANSWERBACK FUNCTION
The following steps will set the horn answerback function to one of two different modes. These steps must be done with the key removed from the ignition switch.
1. Press and hold the LOCK button for 4 to 10 seconds, then press the UNLOCK button during this time. 2. Release the LOCK and UNLOCK buttons at the same time. A tone alarm/buzzer will sound to indicate the current mode: One tone/buzzer: The horn will sound if the doors are locked with the keyless entry system. Two tones/buzzers The horn will not sound, even if the doors are locked or unlocked with the keyless entry system.
Three tones/buzzers: (For Eclipse, Eclipse Spyder, Galant, and Lancer ONLY): The horn will sound if the doors are already locked and the keyless entry system is used again. In this mode, the horn will only sound when the keyless entry LOCK button is pressed again to confirm that the doors are already locked.
The keyless entry system answerback/confirmation functions from the turn signal/hazard lights and horn can each be turned on and off as desired using the following procedures. All procedures must be done with the key OFF and removed from the ignition switch.
if this doesn't do the trick then the output from the ETACS module to the turn signal lamps is not present. you may have a faulty module, or wiring problem.
|
|
|
Post by dzuwel on Jul 8, 2011 7:49:47 GMT -5
UR DA MAN BUGZZY!!!!!!!!! I tried it and it works, the answerback function from hazard lights returned....THANKS A LOT!!!!!
|
|
|
Post by lostone on Sept 5, 2016 12:14:44 GMT -5
Yup. Mine work now.
|
|